NF-30 Semi-Automatic Tube Filling and Sealing Machine
10 to 30 tubes a minute, on single-phase power — for small batches and new products
Filling tubes by hand is slow and every tube comes out a little different. This machine fills and seals them for you: an operator drops each empty tube into its holder, and the machine lines up the print, fills the tube, seals the tail and stamps the lot number. It runs on single-phase power, so it goes in without a new electrical supply. For plastic and laminated tubes; the NF-30M does the same job for aluminum tubes.
1. Output: 10 to 30 tubes a minute, loaded by hand
2. Fill: 5 to 250 ml per tube, within ±1%
3. Tubes: plastic and laminated, Ø13–50 mm, 50–210 mm long
4. Power: single phase. No three-phase supply needed
Is the NF-30 the right size for you?
✓ Yes, if…
- You're filling a new product in short runs, or testing a formulation before scaling up
- You need up to 30 tubes a minute
- Your site doesn't have three-phase power
- One operator loading tubes by hand fits your volume
✕ Buy something else if…
- Your tubes are aluminum → the NF-30M is the aluminum version, sealed by folding rather than heat
- You need more than 30 a minute → the NF-60A feeds tubes automatically at up to 60 a minute
- You don't want anyone loading tubes → every automatic model in the range feeds tubes from a magazine
- You're expecting a benchtop unit → this machine stands on the floor and weighs over 200 kg
Hot Air on the Inside of the Tube
Plastic and laminated tubes are sealed with hot air blown onto the inside of the tube tail, then pressed flat The printed outside isn’t heated directly, so the artwork doesn’t scorch.
Print Lined Up Before Filling
A color-mark sensor and a stepper motor turn each tube until the printed eye-mark faces the right way, so every sealed tail lines up with the front of the tube.
Seal, Stamp and Trim in One Station
The tail is sealed, the lot number is stamped into the seal, and the end is trimmed at the same station — no second machine for coding.
Optional Heated, Stirred Hopper
A double-jacketed hopper keeps products that thicken as they cool — balms, waxes — at a fillable temperature. Available as an option.
Technical specification
Parameter | NF-30 (plastic, laminated) | NF-30M (aluminum) |
Operation | Semi-automatic, tubes loaded by hand | Semi-automatic, tubes loaded by hand |
Output | 10–30 tubes/min | 10–30 tubes/min |
Fill | 5–250 ml | 5–180 ml |
Accuracy | ±1% | ±1% |
Tube diameter | Ø13–50 mm | Ø13–35 mm |
Tube length | 50–210 mm | 50–180 mm |
Sealing | Hot air, pressed flat | Mechanical folding |
Controls | Push buttons; touchscreen optional | Touchscreen |
Motor | 0.75 kW | 1 kW |
Power supply | Single phase, 60 Hz. Built to your U.S. supply; we confirm the voltage with your quote | Same |
Compressed air | Above 0.4 MPa | Above 0.4 MPa |
Dimensions | 1,100 × 800 × 1,600 mm | 1,100 × 800 × 1,600 mm |
Weight | 280 kg | 280 kg |
Options | Heated, stirred hopper; water chiller; touchscreen; finished-tube conveyor | Heated, stirred hopper |
Model comparison
Model | Operation | Tubes | Speed | Fill | Power |
NF-30 / NF-30M | Semi-automatic | Plastic / aluminum | 10–30/min | 5–250 ml | Single phase |
NF-60A | Automatic | Plastic, laminated | up to 60/min | 5–250 ml | Three phase |
NF-80 | Automatic | Plastic, laminated | 50–75/min | 5–250 ml | Three phase |
NF-100 | Automatic | Plastic and aluminum | 80–100/min | 5–180 ml | Three phase |
NF-120 | Automatic, twin station | Plastic and aluminum | 80–120/min | 5–250 ml | Three phase |
Industry Applications
Typical OTC products in U.S. supplement and OTC plants:
Hydrocortisone and Anti-Itch Creams
Short runs of OTC anti-itch creams in plastic or laminated tubes, filled and sealed the same way every time before volume justifies an automatic line.
Zinc Oxide and Petrolatum Ointments
Thick ointments that stiffen as they cool. The optional heated, stirred hopper keeps them fillable through the run.
Medicated Lip Ointments
Small tubes from Ø13 mm, at volumes too low for an automatic machine.
Antibiotic Ointments in Aluminum Tubes
First-aid ointments that need a full barrier against air and light, folded rather than heat-sealed on the NF-30M.
What changing over involves
What changed | What you adjust | Roughly |
Different fill | Pump setting | 15–30 minutes |
Different tube diameter | Tube holders | 15–30 minutes |
Different product | Clean the hopper and pump | 15–30 minutes |
What to check before you buy
Your tube, not a sample tube
Plastic, laminated and aluminum tubes seal in different ways. Ask any supplier to run your tube, not one of theirs.
Plastic or aluminum — or both?
Many semi-automatic fillers seal only one kind of tube. If you run both, ask whether that's one machine or two.
Your power supply
This machine runs on single-phase power. The automatic models need three-phase — check before you choose.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Tubes Before You Order
Send us a few of your empty tubes and a sample of your product. We need your tube to size the holders and set the sealer anyway, so we fill and seal them on the machine and send them back. You’ll see the seal, the code and whether the print still looks right after the heat — on your own tube and your own product, not a sample we chose.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
NF-30 Tube Filling Machine Comprehensive Technical FAQ
Because the format is still changing. The NF-30 takes little floor, wastes little product when you prime it, and changes tube size by swapping the tube holders. It runs on single-phase power, so it goes into a development room without a new electrical supply.
Not on the same machine. Plastic and laminated tubes are sealed with hot air; aluminum tubes are folded. The NF-30 handles plastic and laminated tubes, and the NF-30M handles aluminum.
The operator drops each empty tube into its holder, and the machine does the rest: it lines up the print, fills the tube, seals the tail, stamps the lot number and trims the end. One operator keeps up 10 to 30 tubes a minute.
Thick creams and ointments tend to leave a thread of product behind when the nozzle lifts away, and that thread lands where the seal will be. The NF-30 uses a cut-off nozzle that blows off and cuts off the product at the end of each dose, so the break is clean and the seal area stays clear.
The standard hopper is single-walled. For ointments and balms that thicken as they cool, a double-jacketed heated hopper with a stirrer is available as an option, to keep the product at a fillable temperature through the run.
Since the sealing jaws, hot-air nozzle alignment, and dosing valve cut-offs are entirely driven by pneumatic actuators, the NF-30 requires a reliable source of clean, dry compressed air. The system requires an operating pressure above 0.4 MPa. We recommend pairing the machine with a standard, low-noise oil-water separator air compressor to safeguard the internal pneumatic seals.
No. It runs on single-phase power — the only machine in our tube range that does. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote. The automatic models need three phase.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send Us an Empty Tube and a Sample
Two things decide which machine you need: whether your tubes are plastic, laminated or aluminum, because each is sealed differently, and how many you need a day. Tell us both and we’ll tell you whether a semi-automatic machine is enough.
Better still, send us a few empty tubes and a sample of your product. We’ll fill and seal them and send them back.
Direct from our factory
Lead time confirmed in your quote
Installation and training available
Spare parts listed in your quote