Shrink Sleeve Applicator and Shrink Tunnel
Tamper-Evident Neck Bands for Supplement Bottles
A foil seal under the cap tells your customer the bottle wasn’t opened — but only after they’ve opened it. A band over the cap tells them before they buy.
Two Layers of Tamper Evidence, Not One
Under the cap — an induction seal, foil welded to the bottle mouth. It proves the bottle is intact, but only once the customer has it in their hands and twists the cap off.
Over the cap — a shrink band. It crosses the gap between cap and neck, so it has to be cut or torn before the cap turns. A customer standing in a store can see it, and so can the person checking returns at your distributor.
Most US supplement brands run both. The foil is the seal; the band is what the shelf sees. If your bottling line already has an induction sealer, this is the station that sits right after it.
Two machines do the job. An applicator cuts film from a roll, opens it and drops it over the neck — nothing is glued and nothing presses on the bottle. A tunnel then heats the band so it shrinks tight onto the cap. Without the tunnel the band sits loose.
Why AIPAK Sleeve Applicators
Nothing Sticks to the Bottle
Film comes off a roll as a flat tube, is cut to length and dropped over the neck. Nothing is glued and nothing presses on the container — which is why glass runs the same as PET, with no change but the knife plate.
Applicator and Tunnel from One Supplier
Two machines that have to be timed to each other. Buying them separately means two suppliers pointing at each other when the band comes out crooked or half-shrunk.
We Run Your Bottles First
Send us 30 bottles of each size and a 200 m roll of each film. We band them, shrink them, and send you the result with the rate we actually held — before you order, not after.
Knife Plates for Your Whole Range
Ø25–50, Ø51–90 and Ø91–125 mm. Tell us every bottle size you run and we’ll quote the plates together, rather than leaving you to find out later that one size needs another plate.
Which Pair Do You Need?
Buy them as a pair. An applicator without a tunnel leaves the band sitting loose on the neck. A tunnel without an applicator has nothing to shrink.
The APK-SL50 runs 50 bottles a minute on single-phase power — no new electrical supply needed. The APK-SL150 runs up to 150 and needs three-phase.
The band has to clear the cap, so measure the cap, not the bottle body. And check the tunnel before the applicator: the APK-SH7 takes bottles up to Ø100 mm and 280 mm tall, where the applicator would go to 120. The tunnel is the real ceiling.
PVC, PET and OPS all run. Film thickness differs between the two applicators — 0.03 to 0.13 mm on the APK-SL50, 0.035 to 0.080 mm on the APK-SL150. Tell us your film spec before you choose.
| Entry pair | Line pair | |
| Applicator | APK-SL50 | APK-SL150 |
| Tunnel | APK-SH7 | APK-SH15 |
| Speed | 50 bottles/min | up to 150 bottles/min |
| Bottle Ø | 28–100 mm | 25–125 mm |
| Bottle height | up to 280 mm | up to 350 mm |
| Power | single-phase applicator + tunnel | three-phase |
Sleeve Applicators
The machine that puts the band on.
Shrink Tunnels
The machine that shrinks it down. An applicator without a tunnel leaves the band loose on the neck.
Model comparison
Model | Function | Speed | Bottle Ø | Bottle height | Power |
APK-SL50 | Applicator | 50 bottles/min | 28–120 mm | up to 250 mm | 220 V single-phase, 3 kW |
APK-SL150 | Applicator | up to 150 bottles/min | 25–125 mm | up to 350 mm | three-phase, wired for your U.S. supply, 3 kW |
APK-SH7 | Shrink tunnel | 0–35 m/min | up to 100 mm | up to 280 mm | 7 kW |
APK-SH15 | Shrink tunnel | 0–45 m/min | up to 125 mm | up to 350 mm | 15 kW |
Size the tunnel first. The applicator takes a wider bottle range than the tunnel does — on the entry pair the ceiling is Ø100 mm, where the applicator alone would reach 120.
And treat every speed on this page as a starting point. Bottle shape, cap profile and film all change the rate. We confirm yours on your own samples.
Where Banding Sits on Your Line
NINE STATIONS, ONE LINE
Bottle Unscrambler
Bottle Air Cleaner
Counting Machine
Induction Sealer
Capping Machine
Desiccant or Cotton Inserter
Sleeve Applicator
Shrink Tunnel
Labeller
The band goes on after the cap, because it has to cross the cap-to-neck gap. The tunnel sits immediately after the applicator with nothing between them — the band isn’t held on by anything until it shrinks, so any extra handling in between will move it.
The body label goes on last. A band that’s already shrunk won’t interfere with it.
One thing worth checking: if your line runs faster than the applicator, the applicator becomes your line speed. A 50-bottle-a-minute applicator on a line built for 100 halves your output.
What These Machines Are Banding
Documentation & Selection Support
Verify our specifications and simplify your procurement process with our official documentation.
Product Portfolio
CE Declaration of Conformity
Send Us Bottles and Film
FAQ
A label is glued to the bottle and carries your artwork. A shrink band is a tube of film dropped over the cap with nothing holding it on until heat shrinks it. Its job is to show whether the cap has been turned.
Most brands run both. The foil seal sits under the cap and proves the product is intact. The band sits over the cap and is what a customer sees before buying.
Usually the tunnel. Our applicators take bottles from Ø25 to 125 mm; the smaller tunnel stops at Ø100 mm and 280 mm tall. Send us your bottle and we’ll check both.
We won’t know until we run it. Bottle shape, cap profile and film all change the rate. Send us 30 bottles of each size and a 200 m roll of each film, and we’ll tell you the rate we held — not a headline number.
Electric. We don’t offer a steam tunnel, and we wouldn’t recommend one for supplement bottles. Steam tunnels put moisture into the packing area, and a bottle that leaves the tunnel damp is a bottle your body label may not stick to. They also need a boiler, condensate drainage and regular cleaning of the steam box — three things an electric tunnel doesn’t ask of you.
For neck bands on PVC, PET or OPS film, hot air does the job. Steam earns its place on full-body sleeves with complex bottle shapes, where the film has to pull into a recess — and that’s a different product from what most supplement brands run.
PVC, PET and OPS. Thickness range differs between the two applicators — 0.03 to 0.13 mm on the APK-SL50, 0.035 to 0.080 mm on the APK-SL150. Rolls with a 5 to 10 inch core, bought locally.
The APK-SL150 doesn’t — power only.
Yes. All four machines are built for 60 Hz and wired for your U.S. supply. The APK-SL50 runs on single-phase power; the APK-SL150 and both tunnels need three-phase.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Yes. Our machines are certified and use certified electrical components. Because the exact scope depends on the model and electrical configuration you select, our factory confirms it in writing before production.
Send Us Bottles and Film. Then We'll Talk Speed.
The rate any supplier quotes you is a rate on their bottle, not yours. Send us 30 bottles of each size and a 200 m roll of each film, and we’ll run them and tell you the rate we can hold.
If you already have an applicator or a tunnel, say so — you probably need one machine rather than two, and that changes the quote substantially.
- Reply within one business day
- Trial run on your own bottles, free
- We keep your artwork and specs confidential.