APKZRJ Up Homogenizer Vacuum Emulsifying Mixer
Lid-lift vacuum emulsifier with oil and water phase pots, 50 to 1,000 liters
A cream is two liquids that don’t want to mix. This machine prepares the oil phase and the water phase in their own heated pots, draws both into the main vessel under vacuum, and emulsifies them with a homogenizer running up to 3,500 rpm while a slow mixer keeps the batch turning. The lid lifts clear for cleaning, and stays locked down while the vessel is under vacuum.
1. Capacity: 50 to 1,000 liters per batch
2. Homogenizer: up to 3,500 rpm
3. Three vessels: oil pot, water pot and main emulsifying vessel
4. Heating: electric through a water jacket, or steam
Is the APKZRJ the right size for you?
✓ This is a fit if…
- You make OTC creams, ointments or gels in batches from 50 to 1,000 liters
- Your oil and water phases need to be heated separately before they meet
- You want the lid to lift clear for cleaning and inspection
- You have the headroom — up to 4.55 m with the lid raised on the 1,000-litre model
✕ Buy something else if…
- Your ceiling is low → the fixed-lid APKZRJ-F doesn't need clearance above the vessel Your product carries a heavy powder load that settles → the bottom-homogenizer APKZRJ-B
- Your batches are under 50 liters → 10- and 20-litre models are available
Oil Pot, Water Pot, Main Vessel
Oil-soluble ingredients dissolve in the oil pot and water-soluble ones in the water pot, each at its own temperature. Both are drawn into the main vessel under vacuum through stainless pipes.
Homogenizer and Slow Mixer
A high-speed homogenizer, running at up to 3,500 rpm, breaks the phases into a fine emulsion.
Vacuum from Start to Finish
A water-sealed vacuum pump, with a gas–liquid separator before it, draws the phases in and pulls air out of the product while it’s mixed.
Lid Locked Under Vacuum
A vacuum protection switch stops the lid being raised while there’s vacuum in the vessel. The vacuum is broken through a filtered valve before the lid lifts.
Discharged by Air, Cleaned by Water
The finished product is pushed out through the bottom valve by compressed air. A CIP port on the lid connects to a water supply for cleaning inside the vessel.
Technical specification
| Parameter | APKZRJ-50 | APKZRJ-100 | APKZRJ-500 | APKZRJ-1000 |
|---|---|---|---|---|
| Working capacity | 50 L | 100 L | 500 L | 1,000 L |
| Homogenizer motor | 3 kW | 3 kW | 7.5 kW | 11 kW |
| Homogenizer speed | 0–3,500 rpm | 0–3,500 rpm | 0–3,500 rpm | 0–3,500 rpm |
| Mixer motor | 0.75 kW | 1.5 kW | 2.2 kW | 3.7 kW |
| Mixer speed | 0–60 rpm | 0–60 rpm | 0–60 rpm | 0–60 rpm |
| Dimensions | 2,750 × 2,100 × 1,900 mm | 2,800 × 2,150 × 2,100 mm | 3,800 × 2,800 × 2,700 mm | 3,900 × 3,400 × 3,150 mm |
| Height, lid raised | 2,600 mm | 2,800 mm | 3,950 mm | 4,550 mm |
| Heating | Electric (water jacket) or steam | Same | Same | Same |
| Contact parts | 316L, mirror polished | Same | Same | Same |
| Controls | Siemens PLC and touchscreen | Same | Same | Same |
10, 20, 200, 300, 750 and 2,000-litre models are also available.
Model comparison
Model | Type | Capacity | Homogenizer | Height, lid raised | Best for |
APKZRJ | Lid-lift, top homogenizer | 10–2,000 L | 1.1–22 kW, 0–3,500 rpm | 1.7–4.55 m | Creams, lotions and gels; light powders that float |
APKZRJ-B | Bottom homogenizer | 50–1,000 L | 1.1–22 kW, 0–3,500 rpm | 1.3–3.6 m | Formulas with heavy powders that settle |
APKZRJ-F | Fixed lid | 100–1,000 L | 1.1–22 kW, 0–3,500 rpm | 1.3–3.6 m | Rooms with limited headroom |
APKYGJ | Toothpaste mixer | 300–2,000 L | 5–22 kW, 0–3,500 rpm | 3.55–4.55 m | Toothpaste and tooth gels |
Start with your batch size, then your ceiling. If the room can’t take the lid raised, look at the fixed-lid APKZRJ-F. If your formula carries heavy powders that settle, look at the bottom-homogenizer APKZRJ-B.
Industry Applications
Hydrocortisone and Antifungal Creams
Oil-in-water creams where both phases are heated separately before they meet — the job the oil pot and the water pot are there for.
Diaper-Rash and Skin-Protectant Creams
Thick creams that have to be smooth throughout, with the slow mixer keeping the whole batch turning while the homogenizer works.
Pain-Relief Gels
Clear gels made under vacuum, so they go into the tube without bubbles.
Omega-3 Fish Oil Emulsions
Liquid supplements where fish oil is emulsified into a water phase, so the oil doesn’t separate in the bottle.
Switching Products
There are no change parts on a vacuum emulsifier. Switching from one product to the next means emptying the vessel, cleaning it and setting new temperatures and speeds.
What changed | What you do | Roughly |
Same product, next batch | Discharge, rinse through the CIP port | 15–30 minutes |
Different product | Discharge, clean through the CIP port, lift the lid to inspect | 15–30 minutes |
Different heating temperature | Set on the touchscreen | Seconds |
Different mixing speed | Set on the touchscreen | Seconds |
The vacuum is broken through a filtered valve before the product is discharged and before the lid lifts — the machine won’t let you do either under vacuum.
What to Check Before You Buy
Your batch size, not the vessel size
A vessel is never filled to the top. Ask for the working capacity and size the machine to your usual batch, not your largest one.
How the powder goes in
Toothpaste is mostly powder. Ask whether the powder is drawn in under the liquid surface or poured onto it — that decides whether you get lumps.
How you'll heat it
Electric heating works anywhere. Steam is faster on large vessels but needs a steam supply. Confirm which you have, and confirm your voltage before the machine is built.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Look at Your Formula First
Send us your formula, or just what you’re making and how big your batches are, and we’ll tell you which model and which size suits it before we quote.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Questions About the APKZRJ
A top homogenizer works from above, drawing light powders down from the surface into the shear zone. A bottom homogenizer sits at the base of the vessel, where heavy powders such as zinc oxide and calamine settle, and catches them there. Tell us your formula and we’ll suggest which suits it.
Two things. It draws the oil and water phases into the main vessel, and it pulls air out of the product while it mixes, so the finished cream comes out smooth and free of trapped bubbles.
A slow mixer keeps thick products moving while the homogenizer works. Send us your formula and we’ll confirm before you order.
Oil-soluble and water-soluble ingredients dissolve at different temperatures. The oil pot and the water pot prepare each phase separately, then both are drawn into the main vessel under vacuum and emulsified together.
Through the bottom valve, pushed out by compressed air. The vacuum has to be broken first, through a filtered valve on the lid — the product can’t be discharged while the vessel is under vacuum.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send Us Your Formula — or Just Your Batch Size
Three things decide which emulsifier you need. Your batch size decides the capacity. Your ceiling height decides lid-lift or fixed lid — a lid-lift model needs room above the vessel for the lid to rise. And if your formula carries a heavy powder load that settles, that decides where the homogenizer should sit.
Tell us those three and what you’re making, and we’ll point you to the right model. If you can share your formula, even better — we’ll look at it before we quote.
- Reply within one business day
- A model matched to your batch, ceiling and formula
- Your formulation stays with us
No sales calls — we reply by email or WhatsApp, whichever you gave us.