Home » APC-T2 Multi-Function Labeling Machine
APC-T2 Multi-Function Labeling Machine
The APC-T2 applies labels to two, three or four sides of square bottles as they pass through, at 20 to 120 bottles per minute. It’s the last station on a counting and bottling line, and the one your customer actually sees. If your labels go on crooked or wrinkled, this is what fixes it.
20–120 bpm / Square, flat and round / Two, three or four panels
Panel count set on the screen — go from two panels to four without rebuilding anything
Pre-feed label system — the label is staged before it’s applied, so it lands flat and square
Direct from our factory | Lead time confirmed in your quote | Installation and training available | Spare parts listed in your quote
Is the APC-T2 the right labeler for your line?
✓ This is a fit if…
- You're labeling square, flat or round supplement bottles and tubs
- You need two, three or four labels on one container — front, back and side panels
- Your line runs up to 120 bottles per minute
- You want a batch code or expiry date printed on the label as it's applied
- Your supplement facts panel has to line up with the front label
✕ Look elsewhere if…
- You only label round bottles with one wrap-around label → the APC-T1 costs less
- You're labeling the top of a box or a lid → that's the APC-T3 top face labeler
- You're labeling ampoules or oral liquid vials → the APC-T4 runs those horizontally, at 100 to 200 per minute
- Your line runs faster than 120 bottles per minute → tell us your rate and we'll quote the configuration that keeps up
- Your labels are on sheets, not a roll → this machine feeds from a roll only
Technical specification
Parameter | Value | What this means for you |
Labeling speed | 20 – 120 bottles / min | Match this to your capper and sealer, not your counter |
Container type | Square, flat and round bottles | Two, three or four panels per container |
Container diameter range | 15 – 130 mm | Your bottle has to fall inside this |
Label width range | 15 – 130 mm | Check against your artwork |
Label roll core / outer diameter | 76 mm (3 inch) | Confirm with your label printer before you order |
Labeling accuracy | ±1 mm (Depending on bottle and label squareness) | How square the label lands, bottle after bottle |
Coder | Optional: ribbon date coder or thermal transfer printer (TTO) | Prints the batch number and dates on the label as it’s fed |
Power | 1.2 kW, 60 Hz | Built to your U.S. supply. We confirm the voltage with your quote |
Compressed air | 0.4 MPa, 0.2 m³/h | Small demand — most existing compressors cover it |
Machine dimensions | 2,600 × 1,350 × 1,450 mm | Add conveyor length either side |
Machine weight | 380 kg | — |
The 2000 mm length is the machine itself. Allow conveyor run-in and run-out on both sides so bottles are travelling straight before they reach the applicator.
Model comparison
Model | Speed | Containers | Best for… |
|
APC-T1 | 20–120 btl/min | Round bottles | One wrap-around label on a round bottle | |
APC-T2 | 20–120 btl/min | Square, flat and round bottles | Two, three or four-sided labeling on square containers | You are here |
APC-T3 | 20–120 pcs/min | Flat surfaces | Labeling the top face of boxes, lids and trays | |
APC-T4 | 100–200 btl/min | Ampoules, oral liquid vials | Small vials handled horizontally at higher speed |
All four use the same pre-feed label system and tensioned web. What changes is how the container is presented to the applicator.
Indexing between panels
The bottle is held and indexed between applications, so panel two lands at the same height and offset as panel one. Doing this by hand — or by running the bottle through twice — is where alignment goes wrong.
Panel count is set from the screen. You don’t rebuild anything to go from two panels to four.
Detection that stops before it wastes
The machine checks for a missing bottle, a missing label and a missing ribbon, and stops feeding rather than running on.
A labeler that keeps applying labels to nothing gets through a roll before anyone notices. On a four-panel bottle it gets through four times as fast.
Pre-feed system and tensioned web
The label is staged before the container arrives, rather than pulled from the roll at the moment of application. That’s what keeps placement repeatable as the roll diameter shrinks through a shift.
The web runs under controlled tension between roll and applicator. The coder prints cleanly because the web isn’t slack, and every label is fed to the same length.
Servo drive and adjustable position
Label position is adjustable across the full range from the screen, with photoelectric tracking positioning each application.
The machine stores accumulated counts and working parameters, so a repeat job is loaded rather than re-found.
Ideal Applications & Industries
Square supplement bottles with front and back labels
The front label sells the product and the back label carries the supplement facts. Both have to sit at the same height, or the bottle looks wrong on the shelf.
Bottles with a batch code and expiry date
The coder prints on the label as it’s fed, before it reaches the bottle. The web tension is what keeps the print legible — a slack web smears the code, and a smeared code is a rejected batch.
Square powder tubs with a facts panel
The supplement facts table usually goes on a side panel, and it has to sit at the same height as the front label. A tub that’s labeled front-and-side by two passes never lines up.
What changing over involves
What you changed | What gets adjusted | Roughly how long |
New label roll, same container | Load the roll, thread the web | 15–30 minutes |
Number of panels labeled | Panel count setting on the screen | 15–30 minutes |
Different container size | Conveyor guides, indexing station, applicator height | 15–30 minutes |
Square to round, or back | Guide arrangement and applicator setup | 15–30 minutes |
Panel count is a setting, not a rebuild. Going from two panels to four is entered on the screen. That’s the difference between running a four-panel SKU occasionally and not quoting for it at all.
Stored parameters shorten repeat changeovers. The machine holds working parameters, so a job you’ve run before is loaded rather than re-dialed.
Label supply changes matter more than they look. A different backing thickness or core diameter changes how the web feeds. If you switch label printers, run a test before you run a batch.
Three things to check before you buy any labeling machine
Label placement, bottle after bottle
One label applied straight in a demo proves nothing. Ask how consistent placement is across a full roll, as the roll diameter shrinks. We run your bottles with your labels at factory acceptance testing before the machine ships, and you see the results.
The manual
Your operator threads the web, sets label length and adjusts the applicator. They need an English manual with the settings procedure in it — not a translated parts list. Ask to see it before you order.
Installation and training
The machine runs out of the crate. Getting it labeling cleanly across all your SKUs takes someone who's set one up before. Our engineers install it, dial in each of your bottles, and show your operators how to diagnose a crooked label.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Container and Label Before You Order
Send us your container and a roll of your label. We run them on the machine and send you photos. You decide whether to talk quotes after that.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Deep Dive FAQ
It depends on your bottle diameter range, your line speed, and whether you need a coder for batch and expiry printing. Send us your bottle and label artwork and we’ll reply within one business day. Most quotes include a layout showing where it fits.
If they’re square, flat or round and within the size range, almost certainly. Send us a bottle and a label roll and we’ll run a sample before you order — we’d rather show you than describe it.
Usually one of three things, and often not the machine. Bottles that aren’t traveling straight when they reach the applicator, a label web that’s running slack, or an applicator arrangement set for a different bottle shape. Check those before you adjust anything else.
A coder can be fitted to print on the label as it’s fed, before it reaches the bottle. Tell us what you need to print and we’ll specify it.
Yes. That’s what this machine is for. Panel count is set on the screen, from two panels to four.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
Yes. It’s the last station, after capping and sealing, and it runs on its own conveyor. Tell us your existing conveyor height and belt width and we’ll match it.
Yes. Our machines are certified and use certified electrical components. Because the exact scope depends on the model and electrical configuration you select, our factory confirms it in writing before production.
The machine uses a synchronous top hold-down belt to lock the square bottle in position, preventing any tilting on the conveyor. A single continuous label is applied to the first face, and as the bottle moves forward, special flexible wrapping rollers and corner wiping brushes fold and press the label over the 90° corners face-by-face. That keeps the label smooth across three or four sides, placed to within ±1.0 mm.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send us a bottle and a label roll
We’ll run a sample on our own machine and send you a photo before you commit to anything. If your bottle shape needs a different machine, we’ll tell you which one instead of selling you this.
Send your line layout and we’ll show you where the labeler fits and how much conveyor length you need either side.